101131
在产G20 MDR module with AS-Interface for 4 digital inputs and 2 connections for MDRs
全部替代型号
查看完整报告技术参数
| 电源 | |
|---|---|
| Auxiliary voltage (output) | U AUX | 18 ... 30 VDC PELV |
| Current | 3.5 A continuous current , 5 A (<2 s) , max. 7.5 A (<0,3 s) per motor |
| Current loading capacity | 500 mA , overload and short-circuit protected |
| Input current | ≤ 8 mA (limited internally) |
| Rated operating current | I e | ≤ 35 mA |
| Rated operating voltage | U e | 26.5 ... 31.6 V from AS-Interface |
| Supply | from external auxiliary voltage U AUX |
| 交流 / 直流特性 | |
| Noise immunity | EN 61000-6-2:2005, EN 61326-1:2006, EN 62026-2:2013 |
| Signal delay | < 1 ms (input/AS-Interface) |
| 环境与封装 | |
| Ambient temperature | -25 ... 60 °C (-13 ... 140 °F) |
| Height | 27.5 mm |
| Height 27.5 mm Width 135.5 mm Length 54 mm | Height | 27.5 mm | Width | 135.5 mm | Length | 54 mm |
| Mounting | 2 clips with ∅ 8 mm drill hole |
| Storage temperature | -30 ... 85 °C (-22 ... 185 °F) |
| 其他 | |
| AS-Interface | EN 62026-2:2013 |
| AS-Interface specification | V3.0 |
| Cable length | 0.35 m |
| Compatible roller motors | Interroll EC310 Interroll EC5000 24 V AI (20 W / 35 W / 50 W) Rulmeca BL3 Itoh Denki PM500XK Itoh Denki PM500XC PULSEROLLER Senergy-IDC MTA MRD50 (A interface, 24 V to 40 W) WWL R-*-H + CE23XX Conveline RM50 |
| Connection | AS-Interface, AUX: Insulation piercing technology Yellow flat cable/black flat cable Inputs/outputs: M8 round plug connector in accordance with EN 61076-2-104 Inputs: LF004-GS1-A (4-pin, bushing contacts, screw lock, A-coded) Matching connector: LM004-Gx1-A or similar Outputs: NF005-SS1-B (5-pin, bushing contacts, snap lock, B-coded). Matching connector: NM005-Sx1-B or similar |
| Degree of protection | EN 60529:2000 |
| Directive 2014/30/EU | EN 62026-2:2013 |
| Directive 2014/30/EU EN 62026-2:2013 | Directive 2014/30/EU | EN 62026-2:2013 |
| Emitted interference | EN 61000-6-4:2007 |
| Fieldbus standard | EN 62026-2:2013 |
| ID1 code | 6 |
| ID2 code | E |
| ID code | A |
| Input | EN 61131-2:2007 |
| Input filter | 2 ms |
| IO code | 7 |
| IO code 7 ID code A ID1 code 6 ID2 code E | IO code | 7 | ID code | A | ID1 code | 6 | ID2 code | E |
| LED AUX | ext. auxiliary voltage U AUX ; dual LED green/red green: voltage OK red: reverse voltage |
| LED DIR | Motor rotation direction; yellow LED |
| LED ERR | Motor fault: 2 LED yellow |
| LED FAULT | error display; LED red red: communication error or address is 0 red flashing: overload of sensor supply or external auxiliary voltage U AUX missing |
| LED FUSE | Motor power supply; 2 green LEDs |
| LED IN | switching state (input); 2 LED yellow |
| LED MOT | Motor active; 2 yellow LEDs |
| LED PWR | AS-Interface voltage; green LED green: voltage OK green flashing: address 0 or sensor supply overload or external auxiliary voltage U AUX missing |
| Length | 54 mm |
| Mass | 220 g |
| Motor fault | Digital input NPN, U 0 = 3.3 V, R i = 52 kΩ 0 (no error) ≥ 40 µA 1 (error) ≤ 30 µA |
| MTBF | 98 a |
| Node type | A/B node |
| Note | The flat cable routing is designed for 100 actuation cycles |
| Number/Type | 2 Inputs for 3-wire sensors (PNP), DC |
| Overload protection | Fuse 5 A, I 2 t = 53.7 A 2 s per motor |
| Profile | S-7.A.E |
| Required gateway specification | ≥ V2.1 |
| Rotation direction signal | U D | Off / ≥ (U AUX - 1.0 V) at no-load R i = 5.6 kΩ, R LOAD ≥ 5 kΩ AS-Interface data bit D2 = 0: U D = Off |
| Switching point | according to DIN EN 61131-2 0 (undamped) ≤ 0.5 mA 1 (damped) ≥ 2.0 mA |
| UL File Number | E223772 "For use in NFPA 79 Applications only" |
| Velocity signal | U S | 1.4 … 13 V at no-load R i = 5.6 kΩ, R LOAD ≥ 35 kΩ Control via parameter P2:0 |
| Width | 135.5 mm |
器件图片
技术资料
该型号暂未收录资料。