全部替代型号
查看完整报告技术参数
| 电源 | |
|---|---|
| Load current | max. per channel +/- 200 mA , short-circuit protected |
| No-load supply current | I 0 | max. 100 mA |
| Operating voltage | U B | 9 ... 30 V DC , Reverse polarity protection |
| Voltage drop | U d | high level max. U B -6 V low level max. 5 V |
| 交流 / 直流特性 | |
| Noise immunity | EN IEC 61000-6-2:2019 |
| Output frequency | max. 200 kHz |
| Rise time | ≤ 2 µs |
| 环境与封装 | |
| Operating temperature | -40 ... 70 °C (-40 ... 158 °F) -40 ... 80 °C (-40 ... 176 °F) (for dielectric strength version) |
| Storage temperature | -40 ... 80 °C (-40 ... 176 °F) |
| 其他 | |
| Axial | ≤ 100 N |
| Axial ≤ 100 N Radial ≤ 300 N | Axial | ≤ 100 N | Radial | ≤ 300 N |
| Climatic testing | DIN EN 60068-2-78 , no moisture condensation |
| Connector | M12 connector, 8-pin M12 connector, 5 pin M23 connector, 12-pin , clockwise rotation M23 connector, 12-pin , counter clockwise rotation |
| Degree of protection | DIN EN 60529, IP65, IP66, IP67 |
| Detection type | photoelectric sampling |
| Diameter | 93 mm |
| Duty cycle | 1/2 ± 10 % |
| Emitted interference | EN IEC 61000-6-4:2019 |
| Flange | aluminum, blank |
| Housing | powder coated aluminum |
| Housing powder coated aluminum Flange aluminum, blank Shaft Stainless steel 1.4305 / AISI 303 | Housing | powder coated aluminum | Flange | aluminum, blank | Shaft | Stainless steel 1.4305 / AISI 303 |
| Length | 84.5 mm |
| Length 84.5 mm Diameter 93 mm | Length | 84.5 mm | Diameter | 93 mm |
| Load resistor | ≥ 1 kΩ |
| Mass | < 1100 g without cable |
| Output type | HCHTL |
| Permissible cable length | max. 300 m with a wire cross section ≥0.34 mm 2 |
| Pulse count | max. 5000 |
| Pulse counts < 3600 | 90 ° ± 9 ° electrical |
| Pulse counts ≥ 3600 | 90 ° ± 25 ° electrical |
| Pulse counts < 3600 90 ° ± 9 ° electrical Pulse counts ≥ 3600 90 ° ± 25 ° electrical | Pulse counts < 3600 | 90 ° ± 9 ° electrical | Pulse counts ≥ 3600 | 90 ° ± 25 ° electrical |
| Radial | ≤ 300 N |
| Rotational speed | max. 6000 min -1 for IP65 max. 3000 min -1 for IP66/IP67 |
| Shaft | Stainless steel 1.4305 / AISI 303 |
| Shaft insulation | max. 2.5 kV (for dielectric strength version) |
| Shock resistance | DIN EN 60068-2-27, 200 g , 6 ms |
| Starting torque | ≤ 0.1 Nm for IP65 ≤ 0.15 Nm for IP66/IP67 |
| Terminal compartment | Cable duct for cable diameter ∅4.0 mm ... 9.5 mm |
| UL approval | E223176 , cULus Listed, General Purpose, Class 2 Power Source, Type 1 enclosure , if UL marking is marked on the product. For use in NFPA 79 Applications only. adapters providing field wiring on request |
| Vibration resistance | DIN EN 60068-2-6, 20 g , 10 ... 2000 Hz |
器件图片
技术资料
该型号暂未收录资料。