Все аналоги
Полный отчётТехнические параметры
| Питание | |
|---|---|
| No-load supply current | I 0 | < 18 mA at 24 V Operating voltage |
| Operating voltage | U B | 10 ... 30 V DC |
| Switching current | max. 100 mA , resistive load |
| Switching voltage | max. 30 V DC |
| Voltage drop | U d | ≤ 1.5 V DC |
| Характеристики по постоянному и переменному току | |
| Ripple | max. 10 % |
| Switching frequency | f | 1000 Hz |
| Условия эксплуатации и корпус | |
| Ambient temperature | -40 ... 60 °C (-40 ... 140 °F) , cable, fixed installation -20 ... 60 °C (-4 ... 140 °F) , movable cable not appropriate for conveyor chains |
| Height | 50.6 mm |
| Height 50.6 mm Width 15 mm Depth 41.7 mm | Height | 50.6 mm | Width | 15 mm | Depth | 41.7 mm |
| Storage temperature | -40 ... 70 °C (-40 ... 158 °F) |
| Другое | |
| Adjustment range | 200 ... 1400 mm |
| Ambient light limit | EN 60947-5-2 : 60000 Lux |
| Cable length | 0.3 m |
| CCC approval | CCC approval / marking not required for products rated ≤36 V |
| Communication interface | IEC 61131-9 |
| Compatible master port type | A |
| Connection | fixed cable 300 mm with M8 x 1 male connector; 4-pin |
| Control elements | Light-on/dark-on changeover switch |
| Degree of protection | IP67 / IP69 / IP69K |
| Depth | 41.7 mm |
| Detection range | 2 ... 1400 mm |
| Detection range max. | 2 ... 1400 mm |
| Detection range min. | 100 ... 200 mm |
| Device ID | 0x111101 (1118465) |
| Device profile | Identification and diagnosis Smart Sensor type 2.4 |
| Diagnostic Coverage (DC) | 0 % |
| Diameter of the light spot | approx. 50 mm at a distance of 1400 mm |
| Function indicator | LED yellow: constantly on - object detected constantly off - object not detected |
| Housing | PC (Polycarbonate) |
| Housing PC (Polycarbonate) Optical face PMMA | Housing | PC (Polycarbonate) | Optical face | PMMA |
| Interface type | IO-Link ( via C/Q = pin 4 ) |
| IO-Link revision | 1.1 |
| LED risk group labelling | exempt group |
| Light source | LED |
| Light type | modulated visible red light |
| Mass | approx. 41 g |
| Min. cycle time | 2.3 ms |
| Mission Time (T M ) | 20 a |
| MTTF d | 724 a |
| Opening angle | 2 ° |
| Operation indicator | LED green: constantly on - power on flashing (4Hz) - short circuit flashing with short break (1 Hz) - IO-Link mode |
| Optical face | PMMA |
| Process data width | Process data input 1 Bit Process data output 2 Bit |
| Product standard | EN 60947-5-2 |
| Protection class | III |
| Reference target | standard white, 100 mm x 100 mm |
| Response time | 0.5 ms |
| Signal output | 2 push-pull (4 in 1) outputs, short-circuit protected, reverse polarity protected, overvoltage protected |
| SIO mode support | yes |
| Switching type | The switching type of the sensor is adjustable. The default setting is: C/Q - Pin4: NPN normally open / light-on, PNP normally closed / dark-on, IO-Link /Q - Pin2: NPN normally closed / dark-on, PNP normally open / light-on |
| Transfer rate | COM2 (38.4 kBit/s) |
| UL approval | E87056 , cULus Listed , class 2 power supply , type rating 1 |
| Usage category | DC-12 and DC-13 |
| Width | 15 mm |
Изображения
Документы
К этому компоненту пока не привязаны документы.