Все аналоги
Полный отчётТехнические параметры
| Питание | |
|---|---|
| No-load supply current | I 0 | Emitter: ≤ 14 mA Receiver: ≤ 13 mA at 24 V supply voltage |
| Operating voltage | U B | 10 ... 30 V DC |
| Switching current | max. 100 mA , resistive load |
| Switching voltage | max. 30 V DC |
| Voltage drop | U d | ≤ 1.5 V DC |
| Характеристики по постоянному и переменному току | |
| Ripple | max. 10 % |
| Switching frequency | f | 1000 Hz |
| Условия эксплуатации и корпус | |
| Ambient temperature | -40 ... 60 °C (-40 ... 140 °F) , cable, fixed installation -25 ... 60 °C (-13 ... 140 °F) , movable cable not appropriate for conveyor chains |
| Height | 37.1 mm |
| Height 37.1 mm Width 11 mm Depth 21.5 mm | Height | 37.1 mm | Width | 11 mm | Depth | 21.5 mm |
| Storage temperature | -40 ... 70 °C (-40 ... 158 °F) |
| Другое | |
| Ambient light limit | EN 60947-5-2 : 30000 Lux |
| Cable length | 0.3 m |
| Communication interface | IEC 61131-9 |
| Compatible master port type | A |
| Connection | 300 mm fixed cable with M12 x 1, 4-pin connector |
| Control elements | Receiver: light/dark switch |
| Degree of protection | IP67 / IP69 / IP69K |
| Depth | 21.5 mm |
| Device ID | Emitter: 0x110401 (1115137) Receiver: 0x11030B (1114891) |
| Diagnostic Coverage (DC) | 0 % |
| Diameter of the light spot | approx. 65 mm at a distance of 1 m |
| Effective detection range | 0 ... 12 m |
| Emitter | OBE12M-R100-S-IO-0,3M-V1 |
| Function indicator | Yellow LED: Permanently lit - light path clear Permanently off - object detected Flashing (4 Hz) - insufficient operating reserve |
| Housing | PC (Polycarbonate) |
| Housing PC (Polycarbonate) Optical face PMMA | Housing | PC (Polycarbonate) | Optical face | PMMA |
| Interface type | IO-Link ( via C/Q = pin 4 ) |
| IO-Link revision | 1.1 |
| LED risk group labelling | exempt group |
| Light source | LED |
| Light type | modulated visible red light |
| Mass | Emitter: approx. 10 g receiver: approx. 10 g |
| Min. cycle time | 2.3 ms |
| Mission Time (T M ) | 20 a |
| MTTF d | 462 a |
| Opening angle | 3.7 ° |
| Operation indicator | LED green: constantly on - power on flashing (4Hz) - short circuit flashing with short break (1 Hz) - IO-Link mode |
| Optical face | PMMA |
| Parameterization indicator | IO link communication: green LED goes out briefly (1 Hz) |
| Process data width | Emitter: Process data output: 2 Bit Receiver: Process data input: 2 Bit Process data output: 2 Bit |
| Product standard | EN 60947-5-2 |
| Protection class | III |
| Receiver | OBE12M-R100-E5F-IO-0,3M-V1 |
| Response time | 0.5 ms |
| Signal output | 1 PNP, short-circuit protected, reverse polarity protected |
| SIO mode support | yes |
| Stability alarm output | 1 PNP, inactive when level falls below operating reserve after approx. 5 s. Immediately inactive if the beam is interrupted 4 times during the flashtime. |
| Switching type | The switching type of the sensor is adjustable. The default setting is: C/Q - Pin4: PNP normally open / dark-on, IO-Link Alarm output - Pin2: PNP normally closed |
| Test input | emitter deactivation at +U B |
| Threshold detection range | 15 m |
| Transfer rate | COM2 (38.4 kBit/s) |
| UL approval | E87056 , cULus Listed , class 2 power supply , type rating 1 |
| Usage category | DC-12 and DC-13 |
| Width | 11 mm |
Изображения
Документы
К этому компоненту пока не привязаны документы.